KUKA機器人保養ABB安全區域和中斷一起連用案例解析

MODULE XXXX

!定義臨時全局區域數據

VAR wztemporary conveyor;

!定義全局區域形狀數據

VAR shapedata volume;

!定義中斷識別號

VAR intnum empty;

!定義全局區域形狀設定數據位置點1和點2

pers pos corner1:=[363.41,41.87,317.67];

pers pos corner2:=[613.41,-258.13,567.67];

!定義計算位置示教點

VAR

robtarget AnQua:=[[363.41,41.87,317.67],[0.261461,0.63764,0.229939,0.687155],[0,0,1,1],[9E+09,9E+09,9E+09,9E+09,9E+09,9E+09]];

!定義左右移動位置點

TASK

VAR

robtarget Zuo_AnQuanDian:=[[444.89,-401.76,501.87],[0.0966565,0.923747,0.326119,0.176057],[-1,0,0,0],[9E+09,9E+09,9E+09,9E+09,9E+09,9E+09]];

TASK

VAR

robtarget You_AnQuanDian:=[[444.90,-164.34,501.86],[0.0966831,0.923746,0.32611,0.176061],[-1,0,1,0],[9E+09,9E+09,9E+09,9E+09,9E+09,9E+09]];

!安全區域定義

PROC AnQuanQuYu_CheShi()

!計算安全區域大小

corner1.x:=AnQua.trans.x;

corner1.y:=AnQua.trans.y;

corner1.z:=AnQua.trans.z;

corner2.x:=AnQua.trans.x+250;

corner2.y:=AnQua.trans.y-300;

corner2.z:=AnQua.trans.z+250;

!定義一個箱形全局區域

WZBoxDef \Outside, volume, corner1, corner2;

!啟用全局區域限制監控

!WZLimSup \Temp, conveyor, volume;

!啟用全局區域，設置數字信號輸出

WZDOSet \Temp, conveyor, \Before, volume, ZhongDuan1,1;

!停用臨時全局區域監控

!WZDisable conveyor;

!重新啟用臨時全局區域監控

!WZEnable conveyor;

!擦除臨時全局區域監控

!WZFree conveyor;

!調用中斷例行程序

ZhongDuan;

 

!移動左示教點（在安全區外，會觸發安全區）

Movej Zuo_AnQuanDian,v500,fine,tool0\WObj:=wobj0;

!Movej You_AnQuanDian,v500,fine,tool0\WObj:=wobj0;

!Movej Qian_AnQuanDian,v500,fine,tool0\WObj:=wobj0;

!Movej Hou_AnQuanDian,v500,fine,tool0\WObj:=wobj0;

ENDPROC

 

!中斷例行程序

PROC ZhongDuan()

!將中斷與軟中斷程序相連

CONNECT empty WITH QianHou_ZhongDuan;

!當中斷識別號ZhongDuan1置為1時，自動執行軟中斷程序（QianHou_ZhongDuan）。

ISignalDO ZhongDuan1, 1, empty;

ENDPROC

!軟中斷程序

TRAP QianHou_ZhongDuan

!定義中斷發生時的保存位置的程序點

VAR robtarget p1;

!停止機械臂的移動

StopMove;

! 發生中斷時，存儲路徑

StorePath;

!讀取中斷發生的位置保存給p1

p1:=CRobT();

!中斷發生后執行網右走程序

Movej Hou_AnQuanDian,v500,fine,tool0\WObj:=wobj0;

!中斷結束后移動到發生中斷時的位置

MoveL p1,v500,fine,tool0\WObj:=wobj0;

!中斷之后，恢復路徑（繼續從中斷點移動到Zuo_AnQuanDian示教點）

RestoPath;

!重啟機械臂移動

StartMove;

!完成程序的執行

RETURN;

ENDTRAP

 

來源：廣科智能 轉載注明出處